When using a regulated power supply, connect the. The supply voltage must be. When connecting the transceiver to a cigarette. Do not expose the transceiver to long periods of. Do not place the transceiver in excessively dusty. If an abnormal odor or smoke is detected coming. Contact your. One or more of the following statements may be.
The RBRC program. For information on Ni-Cd battery recycling in your area, call toll free. This equipment generates or uses radio frequency energy. The user could lose the authority to operate this equipment. This equipment has been tested and found to comply with the limits. These limits are designed to provide reasonable protection against. This equipment generates, uses and can generate radio frequency. However, there is no guarantee that the interference will not occur in a.
If this equipment does cause harmful. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that.
Consult the dealer for technical assistance. Selecting Output Power Selecting Offset Direction Selecting Offset Frequency Activating Tone Function Selecting a Tone Frequency To access a repeater which requires an odd-split frequency pair, change the offset frequency from the default which is used by most repeaters.
Note: After changing the offset frequency, the new offset frequency. Note: While using an odd-split memory channel or transmitting, you. No matter which selection you make here, simply pressing [CALL] without pressing. Release [CALL] to quit transmitting. You can also make the transceiver remain in the transmit mode for 2 seconds after releasing [CALL]. However, pressing [REV] after Automatic Repeater Offset has selected an offset split status, exchanges the receive and transmit frequencies.
So, while using a repeater, you can manually check the strength of a signal that you receive. While using a repeater, ASC periodically monitors the strength of a signal that you receive directly from the other station.
ASC does not function if your transmit and receive frequencies are the same simplex operation. This function scans through all tone frequencies to identify the incoming tone frequency on a received signal. You may use the function to find which tone frequency is required by your local repeater. Then you need not. You can quickly recall a programmed channel by simple operation. A total of. Store only one. See page Some repeaters use a receive and transmit frequency pair with a non-standard offset.
If you store two separate frequencies in a memory channel, you can operate on those repeaters without programming the offset frequency and direction. To confirm the transmit frequency, press [REV]. Transmit Offset status and Reverse status are not stored in an oddsplit memory channel. To recall channel 3, for. Press [REV] to display the transmit frequency. These settings, however, are cleared once you select another channel or the VFO mode.
To permanently store the. Use the following procedure to clear an individual memory channel. Note: If you have recalled a memory channel on the non-current band A or B , you cannot select the same channel on the current band to clear.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.
Please check your email for further instructions. Enter a new password. Only Nickel-Cadmium batteries must be replaced or disposed of properly. Limits 37 Using Program Press and release KEY. Belt hook Hand strap To remove the belt hook, pull the belt hook downward while pushing its tabs from both sides. Note: It is recommended to use high quality alkaline batteries rather than manganese batteries to enjoy longer periods of battery life.
Do not use different kinds of batteries together. When the battery voltage is low, replace all four old batteries with new ones. Noise Squelch opened The current squelch level is incorrect.
No speaker Audio output Squelch closed Squelch opened The current squelch level is correct. The recommended duty cycle is 1 minute of transmission and 1 3 minutes of reception. Extended transmissions in the high 2 power mode may cause the back of the transceiver to get hot. Transmitting with the supplied antenna near other electronic 3 equipment can interfere with that equipment. Also, transmitting 4 near a poorly regulated power supply, that is not recommended by KENWOOD , may cause the power supply to output an 5 extremely high voltage.
This voltage could damage both your transceiver and any other equipment connected to the power 6 supply. You can program a different power for band A and B.
These keys change frequencies,. This manual often omits the Tuning control to. Press to move to the next step or to complete the setting 16 in various selection modes such as Function Select or 17 Menu mode. This transceiver employs 4 cursor keys so that you can program most of the functions with only one hand.
In this mode you can change the 4 Last, press [OK] again to complete the setting. In this mode you can recall the 12 above. For appropriate sections in this manual. Press [MENU] to select. The selectable special characters are listed below:? Level 8 48 1 Battery Saver Interval 0. Level 1 Level 2 Selections Default Ref. This combination of elevation and high ERP 5 allows communications over much greater distances 6 than communications without using repeaters. In addition, some repeaters must receive a tone from the 9 transceiver to allow it to access.
For details, consult 10 your local repeater reference. Offset Programming Flow q Select a band. Only when programming odd-split repeater frequencies t Activate the Tone function. If necessary y Select a tone frequency. If necessary If you store the above data in a memory channel, you need not reprogram every time. If the offset transmit frequency falls outside the 3 Press [OK] to complete the setting. Hz Hz Hz Hz 01 The transceiver is programmed for offset direction as shown below.
To obtain an up-to-date band plan for repeater offset direction, contact your national Amateur Radio association. So, while using a repeater, you can manually check the strength of a signal that you receive 3 directly from the other station.
ASC does not function while scanning. ASC causes receive audio to be momentarily intermitted every 3 seconds. ID This function scans through all tone frequencies to identify the incoming tone frequency on a received signal. Then you need not 3 reprogram those data every time. A total of 4 memory channels are available for bands A and B. To recall channel 3, for 15 example, press [ENT] , [0] , [0] , [3].
You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.
Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need. A BAND. Output Power. Selecting Offset Direction Selecting Offset Frequency Activating Tone Function Selecting a Tone Frequency Recalling the Call Channel Reprogramming the Call Channel Out a Memory Channel. Setting Scan Using Program TX Hold Storing a To connect the transceiver with the cigarette lighter.
The recommended duty cycle is 1 minute of transmission and. Extended transmissions in the high. Transmitting with the supplied antenna near other electronic. Also, transmitting. This voltage could damage both your. Selecting lower transmit power is a wise method to. You can program a different power for band. This section introduces you to the basic modes you can.
0コメント